Electronic Packaging Science and Technology. King-Ning TuЧитать онлайн книгу.
joints to a high density of solder joints. The higher the density of I/O, the better the resolution of frequency of a digital electromagnetic wave, because each I/O is designed to transmit a small width of the wave.
At the moment, there are two critically important challenges in electronic packaging technology. The first is the need of denser and denser I/O, which means the diameter of micro‐bump and the pitch between them has to be reduced. As to be shown in Chapter 3, hybrid‐bonds consist of Cu‐to‐Cu bonds together with dielectric‐to‐dielectric bonds are being developed. The second is Joule heating and heat dissipation, which will be discussed in Chapter 9.
About the increase of I/O, from BGA to C‐4 joints, there is a RDL of Cu wires in the upper part of the polymer board. From C‐4 joints to μ‐bumps, there is an RDL of Cu wires at the lower part of the interposer chip. This second RDL is invisible in the figure, but it is new in 3D IC because it does not exist in 2D IC devices, where typically there are only two levels of solder joints. The failure of the new RDL is of concern.
Figure 1.5a and b show synchrotron radiation tomographic images of a 3D IC and part of a 2.5D IC device, respectively. The latter has a length about 4 mm, and a thickness and a height of about 0.5 mm. Due to the weak absorption of X‐ray, the two Si chips and the polymer substrate become invisible. We can see the vertical TSV pillars. Also, the solder balls and the Cu wires are shown clearly. In Figure 1.5a, by using a pair of the BGA balls as the cathode and the anode and by passing 50 mA at 100 °C, following the arrows which indicate the conduction path, we can study time‐dependent failures caused by electromigration and Joule heating, to be discussed in Chapter 10.
Figure 1.5 (a) Synchrotron radiation tomographic images of a similar device as shown in Figure 1.1. Due to the weak absorption of X‐ray, the two Si chips and the polymer substrate become invisible. But the solder balls and the Cu wires are shown clearly. (b) Synchrotron radiation tomographic image of a 2.5D IC device, having a length about 4 mm, and a thickness and a height of about 0.5 mm. The vertical TSV pillars can be seen.
Why do we emphasize electromigration and Joule heating? This is because electronic devices are current–voltage (I‐V) devices, so the applied electric current goes in and out of the devices in an open system. It causes Joule heating and electromigration, which are of key reliability concern. Figure 1.6 is a schematic diagram of the cross‐section of a typical 3D IC device. The structure, in essence, is the same as that shown in Figure 1.4, except that on the right‐hand side, there is a stack of memory chips on a logic chip as the CPU. If we replace the stack by an optical or compound semiconductor or MEMS chip, it becomes heterogeneous integration.
Figure 1.6 Schematic diagram of the cross‐section of a typical 3D IC device.
In comparing the structure of 3D IC to that of 2D IC, the difference is the stacking of multilayer of chips and the interconnects using TSV and μ‐bumps. On processing TSV, the thinner the chip, the easier the drilling of vias. On making μ‐bumps, its melting point should be lower than that of C‐4 joints, so that the latter will not melt upon the melting of the former. Thus, the basic challenges are that the wafer is thinner and the processing temperature is lower.
From the viewpoint of packaging technology, we may say that the essence or the major challenge in 3D IC is to scale down the dimension of packaging structures so that it can match those in the chip technology. There is no Moore’s law in packaging technology, so it has room to shrink.
What are the key functions of electronic packaging? The cell phone held in our hands is a movable electronic packaging product or a mobile computer, which enables us to compute and to communicate with the world around us. The set of chips in the cell phone can be arranged horizontally, side by side, but it takes space. Or they can be arranged vertically, one on top of the other, this is called 3D IC, and it reduces the form factor and takes less space. However, heat dissipation in 3D IC is harder because the packing is denser. When over‐heat occurs, it induces reliability problems. Over all, the product should be electrically, mechanically, chemically, and thermally stable.
1.5 Reliability Science and Engineering
An electronic device in operation is an open system because electrical charges flow in and out of the device. While the number of charges in transport is conserved, entropy production is not. The waste heat in entropy production is Joule heating on the basis of irreversible processes. [4, 5] For electrical conduction, Onsager’s Eq. (1.1) below shows that entropy production is the product of the conjugated flux of j (current density = coulomb/cm2‐sec) and the conjugated driving force of E (electric field E = jρ, where ρ is resistivity). Derivation of the Onsager equation will be given in Chapter 9.
where T is the temperature, V is the volume of sample, dS/dt is the entropy production rate, and j2ρ is the Joule heating per unit volume per unit time. Typically, the power from Joule heating is written as P = I2R = j2ρV, where I is the applied current and R is the resistance of the sample. Thus, j2ρ is power density or Joule heating per unit volume per unit time of the sample, in units of Watt/cm3, and I2R is Joule heating per unit time for the entire sample, in units of Watt. Clearly, this is the reason why we need low‐power devices or low entropy production devices.
While the cost of production of 3D IC can be reduced when it is in mass production, the problem of reliability due to over‐heating has to be solved fundamentally by a smart system design or by design‐for‐reliability (DfR) and by a critical selection in materials integration. To put it simply, we need to design low‐power devices, and also we need to understand heat production (Joule heating) in irreversible processes and heat dissipation in the device structure. [6] Hence, the science and engineering of electronic packaging come into focus.
Entropy production is the most relevant understanding of failure induced by electromigration, thermomigration, and stress‐migration in irreversible processes. [7] Statistical analysis of failure requires the knowing of mean‐time‐to‐failure (MTTF). An example is Black’s equation of MTTF for elctromigration. In Chapter 13, we shall present a unified model of MTTF for electromigration, thermomigration, and stress‐migration on the basis of entropy production.