Dynamic Spectrum Access Decisions. George F. ElmasryЧитать онлайн книгу.
trend. Other path loss models can use different exponent values to model signal scattering and signal absorption.
2 The number of active transmitters in a given proximity. For a given receiver, and during the time of reception, there are different potential combinations of active transmitters where their signal will appear as interference. The sum of interference power from all the transmitting nodes, taking into consideration their distances from the given receiver, has to be modeled. In a dense deployment of 5G cells, this sum of interference power from other transmitters can exceed the noise power threshold that is selected to ensure reliable connectivity.
3 The ambient noise. SIR will be affected by noise power and this noise will depend on the received signal and the interference power. Notably, if a 5G deployment resorts to lower transmission power, the ambient noise impact on SIR can be the larger factor. On the other hand, if a 5G deployment resorts to a high transmission power, the sum of interference power in step 2 above becomes the larger factor.
4 Other factors. There are many other factors that can affect the SIR calculation such as fading and shadowing, transceiver design (e.g., the use of multiple antenna and interference cancelation techniques), and adaptive power control.
A simple representation of SIR at a typical receiving node can be expressed as:
(6.1)
where o represents the origin in the spatial model assuming the receiving node is at the origin of the spatial plan, hio is the fading coefficient of the channel at the receiving node for the signal transmitted from node i, ρi is the transmit power of transmitter i, No is the noise power, Φ is the set of all interfering nodes,7 and Xi expresses the distance between the ith interfering node and o.
Notice that Equation (6.1) performs the following:
1 It puts the receiving node at the origin of the spatial model o making the calculation with respect to o.
2 It creates a probabilistic spatial model where transmitting nodes can be randomly positioned with respect to the origin.
3 It consolidates path loss calculation of the subset of transmitting nodes presumed to cause interference with the receiving node at the origin.
Equation (6.1) can be used in a spatial model to calculate SIR, which can be used in a 5G dense deployment to calculate connectivity and coverage when assigning spectrum resources. In addition, SIR calculation can be used to estimate the capacity and throughput of a given deployment area. This calculation can further lead to collecting metrics that can measure the reliability of the 5G networks.8
6.2.2 SIR and Connectivity
Let us define the metric “connectivity” as the probability that a pair of nodes in a network will be able to exchange information at a specified rate R through a single over‐the‐air hop. There is a threshold β for SIR that can be used in a simple manner to express connectivity where connectivity can be assumed to occur if Pr[SIR > β]. That is, if the estimated SIR is less than β, the node pair would decide that a link is not possible.9 The desired rate R can be expressed in bits per second (bps) and can be estimated from β using the Shannon's equation as follows:
(6.2)
In Equation (6.2), Γ ≥ 1, which represents the collective interference impact on data rate.10 The node pair would calculate SIR from Equation (6.1) and calculate β from Equation (6.2) and decide if single over‐the‐air hop connectivity is possible or not.11
In 5G, connectivity has many use cases. Consider the following use cases:
1 If there are no other cells using the same frequency in the area (5G can be considered to be operating much like Figure 6.4) and there is a single active end user, the coverage area for a given rate is decided by the SIR estimation in Equation (6.1) and the threshold β in Equation (6.2) is calculated in a straightforward manner. If SIR > β, the end‐user device has to simply refrain from transmitting when receiving to avoid SI in order to maintain the desired data rate.
2 If a source and destination pair have to communicate through one or more relay nodes, a path must be found where all of the over‐the‐air hops satisfy Equations (6.1) and (6.2). When there is a single flow, as shown in Figure 6.5, this estimation is also straightforward provided that interleaving of transmit and receive time is done accurately to prevent SI between all node pairs in the path.
3 When there are more than one flow, all flows have only one over‐the‐air hop, and there is one flow per cell, connectivity calculation will use the summation in Equation (6.1) to consider all transmitting and receiving node pairs. This case is illustrated in Figure 6.6. Here, accurate directionality, power control, and narrowing the beam as much as possible can reduce the effect of SI.
4 The general case when there is more than one flow and flows use relay nodes. With this case, there are different ways to describe network connectivity based on the single over‐the‐air hop connectivity. Reaching full network connectivity means that all communicating pairs and all single over‐the‐air hops meet the conditions in Equations (6.1) and (6.2).12 With this case, interleaving transmit and receive time per each node is not sufficient to avoid interference. Spatial separation becomes more complex and DSM is needed to ensure connectivity. This case is covered in more detail in Section 6.2.3.
Figure 6.5 Single flow in a cell area of coverage.
Figure 6.6 Multi‐flow, each with a single hop to a different cell.
6.2.3 General Case Connectivity and Coverage
Connectivity and coverage for the 5G general case are multifaceted. This section covers two important aspects of the general case: transmission capacity and cell overlay. There are more aspects of connectivity and coverage and how they