Stained Glass Work: A text-book for students and workers in glass. Christopher WhallЧитать онлайн книгу.

      Do not cut leafage too much by the outlines of the groups of leaves—or wings by the outlines of the groups of feathers.

      Do not outline with lead lines any forms of minor importance.

      Do not allow the whole of any figure to cut out dark against light, or light against dark; but if the figure is ever so bright, let an inch or two of its outline tell out as a dark against a spot of still brighter light; and if it is ever so dark, be it red or blue as strong as may be, let an inch or two of its outline tell out against a still stronger dark in the background, if you have to paint it pitch-black to do so.

      By this "countercharging" (as heralds say), your composition will melt together with a pleasing mystery; for you must always remember that a window is, after all, only a window, it is not the church, and nothing in it should stare out at you so that you cannot get away from it; windows should "dream," and should be so treated as to look like what they are, the apertures to admit the light; subjects painted on a thin and brittle film, hung in mid-air between the light and the dark.

      CHAPTER VI

      I have mentioned all these points of judgment and good taste we have just finished speaking of, because they are matters that must necessarily come before you at the time you are making the cartoon, the preliminary drawing of the window, and before you come to handle the glass at all.

      But it is now necessary to tell you how the whole of the glass, when it is cut, must be fixed together, so that you can both see it and paint upon it as a whole picture. This is done as follows:—

      First place the cut-line (for the making of which you have already had instructions) face upwards on the bench, and over it place a sheet of glass, as large at least as the piece you mean to paint. Thick window-glass, what glass-makers call "thirty-two ounce sheet"—that is, glass that weighs about thirty-two ounces to the square foot—will do well enough for very small subjects, but for anything over a few square feet, it is better to use thin plate-glass. This is expensive, but you do not want the best; what is called "patent plate" does quite well, and cheap plate-glass can often be got to suit you at the salvage stores, whither it is brought from fires.

      Having laid your sheet of glass down upon the cut-line, place upon it all the bits of glass in their proper places; then take beeswax (and by all means let it be the best and purest you can get; get it at a chemist's, not at the oil-shop), and heat a few ounces of it in a saucepan, and when all of it is melted—not before, and as little after as may be—take any convenient tool, a penknife or a strip of glass, and, dipping it rapidly into the melted wax, convey it in little drops to the points where the various bits of glass meet each other, dropping a single drop of wax at each joint. It is no advantage to have any extra drops along the sides of the bits; if each corner is properly secured, that is all that is needed (fig. 40).

      Some people use a little resin or tar with the wax to make it more brittle, so that when the painting is finished and the work is to be taken down again off the plate, the spots of wax will chip off more easily. I do not advise it. Boys in the shop who are just entering their apprenticeship get very skilful, and quite properly so, in doing this work; waxing up yard after yard of glass, and never dropping a spot of wax on the surface.

      It is much to be commended: all things done in the arts should be done as well as they can be done, if only for the sake of character and training; but in this case it is a positive advantage that the work should be done thus cleanly, because if a spot of wax is dropped on the surface of the glass that is to be painted on, the spot must be carefully scraped off and every vestige of it removed with a wet duster dipped in a little grit of some kind—pigment does well—otherwise the glass is greasy and the painting will not adhere.

      Fig. 40.

      For the same reason the wax-saucepan should be kept very clean, and the wax frequently poured off, and all sediment thrown away. A bit of cotton-fluff off the duster is enough to drag a "lump" out on the end of the waxing-tool, which, before you have time to notice it, will be dribbling over the glass and perhaps spoiling it; for you must note that sometimes it is necessary to re-wax down unfired work, which a drop of wax the size of a pinhole, flirted off from the end of the tool, will utterly ruin. How important, then, to be cleanly.

      And in this matter of removing such spots from fired work, do please note that you should use the knife and the duster alternately for each spot. Do not scrape a batch of the spots off first and then go over the ground again with the duster—this can only save a second or two of time, and the merest fraction of trouble; and these are ill saved indeed at the cost of doing the work ill. And you are sure to do it so, for when the spot is scraped off it is very difficult to see where it was; you are sure to miss some, in going over the glass with a duster, and you will discover them again, to your cost and annoyance, when you matt over them for the second painting: and, just when you cannot afford to spare a single moment—in some critical process—they will come out like round o's in the middle of your shading, compelling you to break off your work and do now what should have been done before you began to paint.

      But the best plan of all is to avoid the whole thing by doing the work cleanly from the first. And it is quite easy; for all you have to do is to carry the tool horizontally till it is over the spot where you want the wax, and then, by a tilt of the hand, slide the drop into its place.

      Further Methods of Painting.—There are two chief methods of treating the matt—one is the "stipple," and the other the "film" or badgered matt.

       The Stipple.—When you have put on your matt with the camel-hair brush, take a stippling brush (fig. 41) and stab the matt all over with it while it is wet. A great variety of texture can be got in this way, for you may leave off the process at any moment; if you leave it off soon, the work will be soft and blurred, for, not being dry, the pigment will spread again as soon as you leave off: but, if you choose, you can go on stippling till the whole is dry, when the pigment will gather up into little sharp spots like pepper, and the glass between them will be almost clear. You must bear in mind that you cannot use scrubs over work like the last described, and cannot use them to much advantage over stipple at all. You can draw a needle through; but as a rule you do not want to take lights out of stipple, since you can complete the shading in the single process by stippling more or less according to the light and shade you want.

      Fig. 41.

      A very coarse form of the process is "dry" stippling, where you stipple straight on to the surface of the clear glass, with pigment taken up off the palette by the stippling brush itself: for coarse distant work this may be sometimes useful.

      Now as to film. We have spoken of laying on an even matt and badgering it smooth; and you can use this with a certain amount of stipple also with very good effect; but you are to notice one great rule about these two processes, namely, that the same amount of pigment obscures much more light used in film than used in stipple.

      Light spreads as it comes through openings; and a very little light let, in pinholes, through a very dark matt, will, at a distance, so assert itself as to prevail over the darkness of the matt.

      It is really very little use going on to describe the way the colour acts in these various processes; for its behaviour varies with every degree of all of them. One may gradually acquire the skill to combine

---

Скачать книгу